semi automatic pet blowing machine

Plastic blow molding machine is also a blow molding machine with good induction function, low-cost blow molding machine, general plastic blow molding machine molding machine and its additives, which can be controlled by formulating, large fluctuations also change product functions, such as adding or

It is not less capacity to increase plastic agent to make hard plastic products. Hard plastic products have excellent stiffness and good water and moisture resistance and oxygen isolation, simple differentiation of the manufacturing process of recycling and analogy, burning treatment will damage the chlorine materials, such as the environment of the Qing Dynasty, and the cost of energy, therefore, packaging constraints And follow the progress we know about environmental protection. Plastic blow molding machine has the most beautiful mechanical strength among several kinds of plastic high-density plastic.

The isolated water vapor can be a variety of good plastics. It is the most serious type of flexible and transparent Machinery Manufacturing Co., Ltd. Its greatest strength is its high puncture strength, high strength against tearing, and excellent resistance to stress cracking. In addition, its heat sealing function ratio is high The density and density of general-purpose plastics are low, so it is a film with excellent base materials and is one of the main defects that form them. Conventional plastic semi automatic pet blowing machine blow molding machines can also use hot / cold cycle blow mold injection techniques, First of all, a special equipment system is needed, and the blow mold is quickly heated and cooled down. Using hot water and steam demand, external boilers have some systems to generate steam, and some other systems are a steam control device.

Now many domestic blow molding machine manufacturers are complicated, and good and evil people are confused. How to choose a suitable blow molding machine and not to spend money is particularly important. In fact, there are many traps and many sales of blow molding machines. Some bought blow molding machines and thought it was cheap to pick them up, but it was not.

Megosztás a facebookon

Feeding in this way optimizes the entire production process,

Once the feed is excessive, it will generally cause uneven blow molding, shake, and high-level noise. In addition, the higher sensitivity of the disturbing data and the generally higher blade wear that results in frequent blade replacements remain to be seen. In order to prevent the blow molding machine from malfunctioning, it is necessary to continue to properly feed the crusher, and these requirements are generally difficult to ensure by manual operation.

Feeding in this way optimizes the entire production process, because those operators no longer need to operate the blow molding machine discontinuously, and then they can be busy with other tasks.In the two-step blow molding process, the material to be blown is pre-blown into particles of about 40 mm in a WLK-type consolidated single-shaft main blow molding machine, and then further blow-molded to about 3 using a NZ type subsequent blow molding machine ~ 10mm final particles, which are especially depicted for secondary blow molding with pre-blow material..

After the operation of a stop switch, the pre-blown particles are now perfectly added to the NZ secondary blow molding machine. The result is that the material can accumulate or is being destroyed due to conflicts and its thermal energy is weakened. Compared with this, the two-step blow molding can make the main blow molding machine non-continuous feeding, where the hopper plays the role of a buffer.

The placement of the two blow molding machines can be chosen one above the other or one behind the other. Compared to general blow molding machines, the second generation blow molding machines are much smaller and require less drive energy. When such a blow molding machine is used for the second destruction of pre-blow molding data, the noise level that occurs automatic pet blowing machine suppliers is much lower than the one-step processing with the same speed (n = 450-500min-1). Because its feeding is uniform, it works at a speed of approximately 450min-1, and there is no problem. The secondary blow molding machine operates according to the operating principle of the cutting machine and is specifically depicted for pre-blown particles

Megosztás a facebookon

The double-station bottle blowing machine is equipped with safety protection devices to ensure the safety of operators and maintenance personnel, including safety door, safety fuse, safety cover, etc. At any time, as soon as the machine is started, the safety protection device must first be properly attached and ensure normal operation. During operation, if any accident or error occurs, first press the emergency stop button, then turn off the main power switch, and then check the cause of the machine failure in time, and then restart it only after confirming that the equipment failure is completely eliminated. The safety protection function of this machine is as follows.

l Before repairing the double-station bottle blowing machine, be sure to turn off the main power switch, and place the 'No Power On' card at a prominent position near the main switch. l Regularly check the safety protection device. If you find that the safety protection device is unstable or does not move, it must be repaired in time. l After repairing, please check whether the tool is in the right position. Do not put it on the machine. l

Please choose suitable hydraulic oil. Before using the machine, fill the oil above the designated scale. l The power supply voltage must be controlled within 10% of the voltage indicated on the equipment nameplate. l The frequency requirement should be controlled within 10% of the frequency indicated on the nameplate. l The normal working temperature of electrical equipment is between 5 ℃ and 40 ℃. l The relative humidity of electrical equipment should be within 50% RH when the maximum ambient temperature is 40 ° C. If the ambient temperature is lower, higher relative humidity can be allowed, such as 90% RH at 20 ° C. l All spare parts together with the machine are designed and manufactured for the machine. Never use it for other purposes, and keep it properly to avoid rust, scratches, and aging.

The current safety door is not closed properly, and no action can be performed; the operation of the front safety door and safety protection device needs to be checked regularly. This machine has perfect alarm information. When an alarm occurs, please refer to this information for appropriate processing. The control voltage on the extruder and automatic operation can only be turned on by the key switch. Unauthorized personnel cannot use these keys. 

Megosztás a facebookon